MSSC MAINTENANCE AWARENESS EXAM 2023-2024 ACTUAL EXAM 300 QUESTIONS AND CORRECT DETAILED ANSWERS WITH RATIONALES (VERIFIED ANSWERS)|AGRADE
MSSC MAINTENANCE AWARENESS EXAM 2023-2024
ACTUAL EXAM 300 QUESTIONS AND CORRECT DETAILED
ANSWERS WITH RATIONALES (VERIFIED
ANSWERS)|AGRADE
Because of its design, an offset chain does not require a connecting link.
For this reason, it is normally used in? - ANSWER- Heavy load and low
speed applications
Multiple strand chains are used? - ANSWER- To transmit a great deal of
power
Compared to a V-belt drive, a chain drive? - ANSWER- Is more
efficient
In the process of installing a chain drive system, the motor and driven
component should be checked for a soft foot condition and excessive
run-out. The shaft run-out should be no more than? - ANSWER- 0.002
Chain sag is measured by rotating the sprockets so there is little or no
chain sag in the _____ side and measuring the sag in the _____ side. -
ANSWER- Taut, slack
A chain should be replaced when its length becomes _____ longer than
the original length. - ANSWER- 3%
Chain sag is measured? - ANSWER- Midway between the sprockets
A special link used to reconnect a chain is called a _____ link. -
ANSWER- Master
A chain puller is a tool used to hold two ends of a chain together while
the? - ANSWER- Master link is installed
When using a chain puller, the jaws are opened and closed by? -
ANSWER- A dial on top of the tool
The three components for a belt drive system are? - ANSWER- Belt,
driver sheave, driven sheave
Pitch is defined as the distance between a point and a? - ANSWERSimilar corresponding point
The pitch circle of a belt drive is? - ANSWER- The place in the belt
which represents the center of the force being transmitted by the belt
A belt drive having a 12 inch driver pulley and a 6 inch driven pulley
has a pulley ratio of? - ANSWER- 0.5
In the calculation of shaft speed and shaft torques of a belt drive system,
which of the following applies? - ANSWER- Shaft speeds are inversely
proportional to pitch diameters
The driven pulley in the belt drive system show is rotating at _____ rpm.
- ANSWER- 1200
One important characteristic of a timing belt is? - ANSWER- It will not
slip during operation
The fractional horsepower (FHP) V-belt, also called a light duty belt is
designed for low power application below _____ Hp. - ANSWER- 7.5
The V-belt should ride _____ in the groove with its top near the top of
the sheave; the V-belt does not touch the _____ of the sheave. -
ANSWER- High, bottom
A _____ should be used to check for sheave groove wear. - ANSWERSheave gauge
The maximum allowable deflection force on a belt is _____ than the
minimum deflection force. - ANSWER- 50% greater
Belt span is defined as the? - ANSWER- Distance between the points on
the sheaves where the belt touches each sheave
The most basic way to test the tension of a belt is to? - ANSWER- Your
sense of touch
When connecting a 3-phase motor the three lines (T1,T2 and T3) are
usually connected to __________. - ANSWER- - L1, L2, and L3
Electricians use __________ to prevent damage to electrical wiring
running to the machine. - ANSWER- - rigid and flexible conduit
When the wire or foil strip inside a fuse melts, the fuse is said to be
__________. - ANSWER- - blown
The difference between a fuse and a circuit breaker is __________. -
ANSWER- - circuit breakers can be reset and used again
The amount two electrical waveforms are out of phase is measured in
__________. - ANSWER- - degrees
The type of overload protection that protects the motor by disconnecting
it physically instead of electrically is a(n) __________. - ANSWER- -
overload clutch
Which of the following is an advantage of a circuit breaker over a fuse?
- ANSWER- - Can be reset
*T or F
The minimum number of sets of contacts a motor starter has depends on
the number of power leads the motor requires. - ANSWER- - True
Category | Exams and Certifications |
Comments | 0 |
Rating | |
Sales | 0 |